Arduventure (RPG)

There is a reset button near the usb port on the Arduboy. It’s a timing thing, I don’t remember the exact timing, but try pressing upload, waiting a moment then pressing the reset button on the Arduboy before the upload (on a different sketch) has finished. If that doesn’t work after a few tries, try pressing the reset button then upload. I think it’s the first way though if I’m remembering correctly.

Thank you for the suggestion, I tried both ways, about 10 times each and still did not go through.
Thank you though!

Holding the UP button while powering up should enter flashlight mode. The RGB LED to the left of the display should light up white. Is this happening for you? If so, you should then be able to upload a new sketch.
http://community.arduboy.com/t/arduboy-gets-a-life-conways-game-of-life/578/10

1 Like

Thank you so much, that worked perfectly!

1 Like

Please make a sequel I loved it

Trying to figure out what is causing the units to lock up… We had this problem before where Arduventure took up too much ram and overwrites an address in RAM that is used to indicate a software reset.

But now we are using the latest bootloader on the Arduboy which moves the position in ram way out to the end, so this shouldn’t occur.

I’m pretty sure I remember testing this, is it possible these are being compiled with older versions of arduino?

@MLXXXp any suggestions? are you able to test this?

1 Like

Hello @karman and @MathiasTonia can you please tell us what version of Arduino you were running?

It looks like it’s an issue with Arduino 1.6.12 (possibly earlier, works just fine in 1.6.7, checking others…) and above broke something for us.

The flashlight mode will work to get it back, but you will need to close all instances of Arduino. Unplug and turn off the Arduboy and wait for the COM port to disappear. Then you can hold the up button while turning on the power, this will turn on the RGB led to full white indicating it’s ready to be programmed.

For beginners it’s not recommended to install this right now and if you do run into this issue check this thread and post your issues here:
http://community.arduboy.com/t/cant-upload-sketches-after-arduventure

1 Like

Hi everyone,

I’m new here and I really want to try this game !
Still not a good idea to download it ?
I can’t wait xD.

@Generu This demo I think will still work with the updated Arduboy library and Arduino IDE 1.6.7 it looks like. It can just make it difficult to flash your unit. You might need to put it into flashlight mode to flash a new game.

any new progress on the game? seems like no updates in months

Yep lots of progress, but we are keeping it off the radar :smiley:

6 Likes

I’m hoping we can get a new teaser out soon!

2 Likes

Yes me too, but @DSSiege11 needs to finish the banner and title screen :laughing: :laughing: :laughing:

2 Likes

It’s coming, when it comes out, you won’t miss it! We are going to try and plan some special launch for it, maybe even do something really special… uh… :wink:

3 Likes

Yeah, we’re working on this, but we took it of the grid until finished.

it should have:

  • a map bigger than the one of Zelda’s “link’s awakening”
  • 4 different worlds
  • multiple chiptune songs

Can’t spoil it all can we now :wink:

8 Likes

why yes, yes we can spoil it all.

1 Like

Post made on April 1st… :stuck_out_tongue:

2 Likes

@rawsome any progress on that poke clone you mentioned in Oct '15

That would be a seriously cruel joke ; n ;

True … it was a post on april 1st, but not a joke, we are still working on Arduventure.
I’ll make a video soon, but not before the 15th of april.

2 Likes