VGA1306 (VGA-out for DIY Arduboys implemented on an FPGA!)

I’ve hooked up the VGA adapter to my HomeMade DevKit with NES controller board and proto flash cartridge. It’s like an Arduboy console now :smiley:

It’s awesome seeing Arduboy on my TV with huge pixels :smiley:

6 Likes

3 Likes

lets try the real thing :wink:

5 Likes

3 Likes

I just couldn’t help myself with this one.

3 Likes

Having so much fun with this.

2 Likes

Is VGA 1306 compatiable with Arduboy?
(or rather, is VGA 1306 similar to the 1306 display we find out there?)
If so, are there any video out (HDMI, mini DP are OK) format for someone with original Arduboy library (the one that support SSD 1309?)

The FPGA emulated the SSD1306 that the Arduboy uses in my image it’s wired to the test pads for the Arduboys OLED, both can be run simultaneously as in the photo.

I doubt it would be much work for @uXe to add SSD1309 support since the displays are so similar. HDMI is possible with a VGA to HDMI adaptor I’m not sure if this board has enough pins available to do HDMI but it would certainly be possible to do HDMI with an FPGA.

1 Like

Not wanting to take thing too off topic but I’ll close the audio discussion up here with this. I was too eager to wait for the 2.2k Ohm so I tested one channel using a bunch of 0.5 Ohm resistors I had and wow 2 two channels will be amazing.

Getting back on topic I’ve been thinking how handy it could be for other projects to support more oled controllers.

1 Like

Certainly achievable… you can even potentially have multiple selectable FPGA configurations onboard:

http://hedmen.org/icestorm-doc/icestorm.html#Using-multiple-configurations

Any particular controllers you had in mind though?

3 Likes

SH1106 seem to be a popular alternative to SSD1306 in many projects. And recompiling is not always an option or may be a lot of messing around when switching back and forth between OLED and VGA.

@Mr.Blinky figured how to hex between ssd1306 and ssd1309 so this one wouldn’t be an issue.

SSD1327 128x128 could provide some interesting results as could SSD1329 96x96

Difference between SSD1306 / SSD1309 is one of the configuration commands, and the FPGA code ignores all commands anyway and only listens for the data, so SSD1309 should work fine.

SH1106 - the issue here is that the page address does not automatically increment. So you need to manually set the page addresses during the frame… which means the DC pin is being toggled during the frame and this upsets the FPGA code!

I did write a temporary workaround for trying out the VGA1306 board with @Mr.Blinky’s streaming-bootloader demo, which uses this page-addressing mode for maximum SSD1306 / SH1106 cross-compatibility…

Just needed to replace this portion of Verilog:

always @(posedge wclk) // Write memory
begin
  if (write_en) begin
    mem[waddr] <= din; // Using write address bus
    waddr_r <= waddr_r + 1; // Increment address
  end
  else begin
    waddr_r <= 0; // 'VSYNC'
  end
end

with this:

always @(posedge wclk) // Write memory
begin
  if (write_en == 1 && waddr_r < 8192) begin
    mem[waddr] <= din; // Using write address bus
    waddr_r <= waddr_r + 1; // Increment address
  end
  else if (waddr_r == 8192) begin
    waddr_r <= 0; // 'VSYNC'
  end
end

So, yes - a ‘universal’ SSD1306 / SSD1309 / SH1106 version shouldn’t be difficult!

Could definitely be interesting, yes. 16 shades of grey to play with!

The current 3-bit RGB hardware only allows for 8 colours though :face_with_raised_eyebrow: But add another five resistors, and you get 256 colours! :smile:

VGA

2 Likes

Thought I’d better reply to this over here… :smirk:

…if you remove the flash chip from the socket and use some other external device to send the initial configuration to the FPGA in ‘slave mode’, then the four SPI pins (SPI_SO, SPI_SI, SPI_SS_B and SPI_SCK) become available to the user application 49 clock cycles later - and that same external device can then take advantage of those IO!

Details are on page 26/27 of the iCE40 Programming and Configuration Technical Note.

(EDIT: SPI_SS_B and SPI_SCK do have pull-up resistors attached though, which may limit their usefulness! :roll_eyes:)

2 Likes

Hmm…I can tell 32 shades.

these many things make me think of my homemade bridge diode…
Or one of those mililtary circuit board(Fallout junk items) ancient circuit board with no less than 50 of them on board
Wait. it work with SSD1306? :tada:
@Mr.Blinky
If you can give me the sketch for NES controller (for a Arduino Micro), and @uXe figure out how to get one of your board to be, then I might be able to fit all these onto one Proto-shield. With a 3.5mm headphone jack.
That being what I am aiming for, but @uXe’s board is a tad too big.

Have uploaded an ‘SH1106-friendly’ variation of the code - which listens out for the 0xB0 page-address command to achieve VSYNC, instead of relying on the DC pin:

https://github.com/uXeBoy/VGA1306/blob/master/VGA1106.v

2 Likes

Somebody was going to throw away a display that had VGA! so finally I was able to test the board

https://photos.app.goo.gl/2UnoG9BC78zbSLZd8

Thanks a lot @uXe works like a charm and makes me again to want to learn FPGAs :stuck_out_tongue:

1 Like

Great choice of game for your first run!

Probably also time to clean the desk.

1 Like

Ignore @filmote, please don’t ever clean your desk, a good programmer’s desk should be messy :P

1 Like

That’s funny to hear from someone known to clean up codes all the time :P

1 Like

Bammmmm !